ZHENGOU GroupZHENG'OU

Применение

Химическая и тяжёлая промышленность

Воздействие кислот, щелочей и растворителей в сочетании с термоударом. Винилэфирные и полиуретановые системы там, где обычная эпоксидная смола пузырится.

Что этот пол должен выдерживать

Поймите характер разрушения до того, как выбирать систему.

  1. 01

    Acids, alkalis and solvents attack the floor daily — standard epoxy dissolves here.

  2. 02

    Thermal shock from hot processes and cold washdown works coatings loose from the slab.

  3. 03

    Spillage must not reach the concrete — or the ground beneath it.

  4. 04

    Mechanical damage — impacts, pallet edges, trolleys — opens paths for chemicals to attack.

Химическая и тяжёлая промышленность

Рекомендованные системы покрытия

Подбор по нагрузке — универсальной системы не существует, есть подходящая.

01

Vinyl ester heavy-duty anti-corrosion system (fiberglass-reinforced)

Конструкция пола
Vinyl ester primer → fiberglass mat lamination (layers as required) → vinyl ester mortar → vinyl ester topcoat

The fiberglass lamination bridges cracks and carries the chemical load — the standard answer for acid, alkali and solvent duty.

Стандартная последовательность работ

Один и тот же пол из одних и тех же материалов служит на годы дольше, если работы выполнены аккуратно. Шесть шагов ниже — наш стандарт для эпоксидных полов: что делает каждый шаг, по какому стандарту и что мы проверяем при сдаче. Для вашего цеха мы подстроим количество слоёв и толщину под фактические нагрузки, химическую среду и технологическое окно.

  1. 01

    Substrate preparation

    Grinding, repair and drying; the slab must be sound before any corrosion barrier goes on. Defects such as cracks and voids are located and marked one by one, and repaired before any corrosion work starts.

  2. 02

    Vinyl ester primer

    Primer bonds the system to the slab and is the first chemical barrier. Penetration is confirmed zone by zone; under-fed areas get an extra coat.

  3. 03

    Fiberglass lamination

    Fiberglass mat is wetted out layer by layer in vinyl ester — the reinforcement that bridges cracks. Mat overlaps are staggered as the system requires, with air worked out layer by layer.

  4. 04

    Mortar coat

    Vinyl ester mortar builds thickness and levels the reinforced surface. The mortar doubles as the second barrier; corners and pipe penetrations are thickened with a coved transition.

  5. 05

    Topcoat

    Vinyl ester topcoat seals the system into one continuous chemical barrier. After the topcoat, appearance and build are re-checked against the design before handover.

Фото с объектов

Готовые полы, снятые на объекте, — нажмите, чтобы увеличить и рассмотреть детали.

Fiberglass build-up

Multi-layer fiberglass lamination mid-installation.

Topcoat application

Vinyl ester topcoat applied over large areas — the final chemical barrier taking shape.

Completed resin surface

The continuous resin surface before final inspection.

Показательные объекты

Часть объектов, реализованных группой.

  • Jiaxing Geno Electric anti-corrosion project

    Anti-corrosion coating for cable junction boxes and cable trays. Electrical equipment lives in damp, corrosive environments; vinyl-ester systems are applied layer by layer to steel components and junction boxes to lengthen maintenance intervals.

  • Kaide New Energy industrial base (Guangzhou)

    Abrasion-resistant flooring and anti-corrosion works, Lot 1. With a short build programme and overlapping trades at the new-energy base, works were organised as a flowing sequence so flooring and anti-corrosion were handed over together.

  • Wanhua Chemical

    A group framework cooperation newly awarded in 2025. Chemical plants concentrate flooring and anti-corrosion needs in workshops, tank farms and pipe racks; we recommend vinyl-ester or polyurethane systems zone by zone according to the chemicals present.

  • Shougang Group heavy-industrial sites

    Steel and heavy-industry buildings combine abrasion, heat and chemical exposure under one roof. We supply flooring materials to Shougang Group sites, selecting systems zone by zone according to the medium and load each area actually sees.

  • Minth Automotive Europe plant, Serbia

    A 2020 overseas supply project: we exported a complete vinyl ester package — resin, surface coating, fiberglass mats and cloth, corundum sand and application tools — from Shanghai to the buyer's plant in Loznica, Serbia. The floor was built as a fiberglass-reinforced vinyl ester system ("five cloth, seven coat") covering roughly 100,000 m².

Частые вопросы

Что покупатели спрашивают чаще всего при подборе покрытия для пола.

Which chemicals can the system withstand?

The vinyl ester range is tested against acids, alkalis and solvents at defined concentrations — the results are published per product on the site. Send us your chemical list and we confirm the fit.

Подробнее
Why lay fiberglass cloth?

Concrete moves and cracks; the fiberglass lamination carries those movements and keeps the chemical barrier continuous above them.

Подробнее
Our plant has both acid and alkali zones — one system?

In many cases yes; where duty differs sharply, we vary the topcoat between zones while keeping one overall programme.

Подробнее
Can you renovate a failed anti-corrosion floor?

Yes — the assessment decides whether the sound layers stay and only the top is rebuilt, or the system is redone from the slab. Both keep the plant running zone by zone.

Подробнее

Продукты, часто применяемые здесь

Подобраны к системам выше; на странице продукта — характеристики и протоколы испытаний.

Винилэфирная финишная эмаль тяжёлой антикоррозионной защитыПолиуретановые и антикоррозионные системы

Винилэфирная финишная эмаль тяжёлой антикоррозионной защиты

Винилэфирная финишная эмаль тяжёлого класса, стойкая к 98% серной кислоте и 50% гидроксиду натрия, сертифицированная по ISO 12944 C5-M, со 3 000 ч стойкости к старению QUV и более чем 15 годами службы на открытом воздухе.

Подробнее
Прозрачная винилэфирная финишная эмаль тяжёлой антикоррозионной защитыПолиуретановые и антикоррозионные системы

Прозрачная винилэфирная финишная эмаль тяжёлой антикоррозионной защиты

Прозрачная винилэфирная финишная эмаль тяжёлого класса с прозрачностью ≥ 90%: 5 000 ч стойкости к УФ-старению, без пожелтения на открытом воздухе 10 лет, сохранение внешнего вида основания.

Подробнее
Винилэфирный средний слой тяжёлой антикоррозионной защитыПолиуретановые и антикоррозионные системы

Винилэфирный средний слой тяжёлой антикоррозионной защиты

Винилэфирный средний слой, стойкий к 98% серной кислоте и 40% гидроксиду натрия; прочность сцепления ≥ 8 МПа со сталью и ≥ 3,5 МПа с бетоном, водонепроницаемость ≥ 1,5 МПа.

Подробнее
Прозрачная винилэфирная грунтовкаПолиуретановые и антикоррозионные системы

Прозрачная винилэфирная грунтовка

Винилэфирная грунтовка с наноразмерным проникновением 5–8 мм, прочностью на растяжение ≥ 3,5 МПа, стойкостью к pH 2–14 и возможностью перекрытия за 1,5 часа.

Подробнее

Расскажите о вашем полу

Пришлите тип основания, площадь и нагрузки на пол. Вы получите рекомендованную систему, конструктив пола и коммерческое предложение — как правило, в течение одного рабочего дня.

Запросить расчёт